Architectural cladding
Wollongong.
Zinc, copper and aluminium roofing and facades for Wollongong, the Illawarra and the South Coast, drafted, folded and installed by our own team.

Exposure changes across Wollongong
The Illawarra puts the escarpment, the surf and a working steelworks within a few kilometres of each other. Thirroul and Austinmer sit in salt spray off the open ocean. Port Kembla adds industrial fallout on top of the salt. Dapto and Albion Park, a short drive inland, see almost neither.
We assess each address for salt, industry and the wind coming off the escarpment, then match the metal, the coating and the fixings to it.
Typical exposure across Wollongong
| Area | Typical zone | Metals we usually recommend |
|---|---|---|
| Beachfront: Austinmer, Thirroul, North Wollongong, Shellharbour | C5 | Aluminium, copper or ventilated zinc with a rinse schedule. |
| Port Kembla and the suburbs downwind of it | C5 | Industrial deposits as well as salt. Coating class confirmed per address. |
| Inner suburbs: Wollongong CBD, Figtree, Corrimal | C3 | All four metals suit most sites. |
| Inland: Dapto, Albion Park, Kiama hinterland | C2 | All four metals, including pre-painted steel. |
Indicative only. Exposure varies street by street, so we confirm it for each address. How corrosion zones work
Systems we install in Wollongong
- View system
Standing seam
25 mm seams on concealed stainless clips. Double lock for roofs, single lock for facades.
- View system
Interlocking panel V25
Flat panels with express joints, in standard widths from 190 to 390 mm or made to suit the site.
- View system
Flat lock
A flat skin with a fine recessed joint, folded and interlocked on all four edges.
- View system
Shingles
Interlocking metal tiles, square, rectangular or diamond, on a 7 mm wall footprint.
- View system
Snaplock
Thin ribs and wide pans, in 25 mm and 38 mm modules, snapped closed by hand.
- View system
Cassette
Large folded trays on a concealed subframe, with a 20 mm recessed joint on all four sides.
Areas we cover
- Wollongong CBD
- Thirroul
- Austinmer
- Bulli
- Corrimal
- Fairy Meadow
- Figtree
- Shellharbour
- Kiama
- Gerringong
- Dapto
- Albion Park
- Helensburgh
- Stanwell Park
Questions
10 answered
Wollongong questions
The questions estimators and drafters answer most often. If yours is not here, send the drawings and we will answer it against your project.
Ask about your projectDo you take work in Wollongong and the Illawarra?
Yes. It is an hour and a quarter from our Sydney workshop, and panels arrive folded to length rather than being made on site.
Does the steelworks change what metal I can use?
It can. Industrial fallout is a different attack from surf spray, and the suburbs downwind of Port Kembla see both. We check the distance and the prevailing wind before settling on a metal and a coating class.
Which metal suits a house at Thirroul or Austinmer?
On the open coast we usually recommend aluminium, copper or ventilated zinc, with a rinse schedule for the faces rain cannot reach. Pre-painted steel is a harder case to make that close to breaking surf.
Can you do a job on the escarpment?
Yes, and wind is the thing to design for rather than salt. Fixing centres come off the wind loads for the actual site and the height on the building, not off a house standard.
How long does a metal roof last on the Illawarra coast?
Inland, zinc runs 80 to 100 years and copper beyond 100. On the open coast those figures hold only if the metal suits the exposure and the sheltered faces get rinsed. Put pre-painted steel on a beachfront house at Austinmer and you are looking at a fraction of its inland life.
Is metal cladding allowed on apartment buildings in Wollongong?
Yes. Zinc, copper, aluminium and steel are single sheets with no combustible core and are listed as non-combustible under NCC 2022 clause C2D10. That is what separates them from the composite panels that were banned. The assessment covers the whole wall assembly, which we confirm per project.
Do you do walls as well as roofs?
Both, and often in the same material. Standing seam runs from a roof plane down a wall as one continuous seam, and interlocking panels, cassettes and shingles are facade systems in their own right.
What do you need to give a price?
Drawings. A plan, a section and an elevation are enough to start, and concept sketches will get you a useful answer. We need the address as well, because exposure changes the metal and the metal changes the price.
Do you work for builders or directly for owners?
Both. Most of our work is for builders and architects, and we also work directly for owners on major renovations.
How fast can you price an Illawarra project?
Send drawings and we return a priced tender within seven days.
Have a Wollongong project on the board?
Send drawings or a brief. Concept sketches are enough to get a useful answer.
You send drawings or a brief
A plan, a section and an elevation are enough.
- 1business day
An estimator replies
Named contact, not a queue.
- 7days
Tender returned
Priced by system, metal and area.

